We offer three turbo Injection kits and two NON turbo Injection kits.
All are 100% fuel and ignition control units.
We also offer Port Injection for all of our kits!

Here is the basic info on our VW Kits.
Die Cast Throttle body
Hand held Controller
Windshield Hand Held Mount
(4) Hi- Flow 600 HP injectors (on turbo version)
Built-in pressure regulator
2.5 BAR MAP Sensor (on turbo version)
Throttle Position Sensor
100% Ignition and fuel control
Idle Air Control
Coolant Temp Sensor
Wide band O2 Sensor
O2 Bung Kit
-06 AN Fuel Inlet Fitting
Gasket Kit


Now these extra items and labor are
included in our kits !!!

1. We program each unit specifically for
your VW combo to start and run out of the box. Our programs are built off real air
cooled VW combos. We have tested these combos on street, drag strip, off road. We also continue to test on
our "in-house" flywheel dyno and chassis dyno testing.

2. Modify the throttle body to make it more snappy and have quicker throttle response.

3. We take the non-used vacuum ports and block them off for higher boost use.
Our VW's do not need all those ports and we definitely don't need any vacuum caps popping off !!!
So we press-in steel balls and seal them up!

4. Our custom VW Gas Tank Fitting converts your stock VW gas tank outlet to AN -6. Includes new screen and
filter!

5. Performance Fuel pump and complete VW install kit for up to 600hp use!!!

6. 3/8" aluminium fuel feed and return line and fittings.

7. All clamps, fittings to complete your install of fuel system.

8. Washable chrome air cleaner , stud and wing nut.

9.This is the best part... UNLIMITED Tech Support from us, a shop that sells them, installs them and also runs
the same units in our own street cars and race cars !!!

10. Modified controller and power cables to 18' that make the install in a rear engine car a breeze!

11. Extended Temp Sensor cable for use in our air cooled engines to give you options for install. You can use
the Type3 dip-stick block-off port or our oil cooler line tee or if you like in the sump!! We will supply you with
all the correct fittings and make the changes in the program to match and do it right the first time.

12. Throttle linkage arm adapter to bolt-up to your standard long accelerator cables!

All of our systems are preset to start, and run out of the box!
Plug it in and drive on same day!!



"NON" Turbo Use Kits.
Preprogrammed Fuel Injection system with complete fuel and
Ignition control. Complete Fuel Pump Install Kit and
unlimited tech help. (No Manifold)
90hp-250hp use.
System works best with a Crank Trigger signal.
More info about our Crank Trigger kits
click here..
Kit for "NON" Turbo Use.
$1399.99

Master "NON" Turbo use Kit. Same as
above but also includes intake "T" manifold kit.
90hp to 250hp.
$1799.99
Pictures of the kit on engine with measurements click here
Also includes:
1x 4-barrel hand Tig welded aluminum "T" manifold with 1 3/4" center section.
See Picture of Manifold click here
1x Pair of matching 1 3/4" End Castings. These have an extra 2" longer clamping
surface for perfect seal.
2x 1 3/4" silicone 7-lair boots.
4x 1 3/4" USA made Clamp-Co Stainless Steel T-Bolt clamps.
System works best with a Crank Trigger signal.
More info about our Crank Trigger kits
click here.

Add Port Injection to your kit!
We can mount one or two injectors in each end-castings manifold for true
Port Injection for maximum throttle response!! Click Here

Port Injection 2x 150hp (up to 300hp use)
One injector on each side. add them to each of your end-castings.
Yes 300hp from just four injectors!!!
This includes 2x USA made CNC injector mounts, Labor to welded in place, All the AN fittings,
hose and labor to extend injector harness and block injector ports in our unit.
Add $275 You must supply your end-castings.
Same but with one set of new stock end-castings add $89.99
Or same but with one set of Turbo end-castings manifolds add $150

Port Injection 4x 150hp (up to 600hp use)
Two injectors on each side. add them to each of your end-castings or your manifolds.
Yes 600hp from just four injectors!!!
This includes 4x USA made CNC injector mounts, Labor to welded in place, All the AN fittings,
hose and labor to extend injector harness and block injector ports.
Add $425 You must supply your end-castings or manifolds.
Same but with one set of new stock end-castings add $89.99
Or same but with one set of Turbo end-castings manifolds. add $150


--------------------------------------------------------------

FiTechVW Fuel Injection
Turbo Base kit.
Preprogrammed Fuel Injection System with Complete
fuel and ignition control. Also includes fuel Pump and
Install Kit. (No Manifold)
Comes with Unlimited Tech Help.
System works best with a Crank Trigger signal.
More info about our Crank Trigger kits
click here.
$1599.99

Master Draw-Throu
Turbo use FiTechVW Kit.
Preprogrammed fuel injection system with complete fuel and
ignition control. Also includes fuel pump and install kit.
Comes with Unlimited Tech Help.
$1799.99
Also includes:
1x 4-barrel hand Tig welded aluminum manifold with 3" inlet to mount to a 3" turbo inlet.
Click here for picture.
1x 3" to 3" straight silicone black boot.
2x USA made Clamp-Co Stainless Steel T-Bolt clamps.
If you need a different size intake boot like 3" to 4" let us know and we will replace for free!
System works best with a Crank Trigger signal.
More info about our Crank Trigger kits
click here.



Master Blow-Throu
Turbo use FiTechVW Kit.
Preprogrammed Fuel Injection System with Complete Fuel Pump
and  Install Kit.
Also Includes Unlimited Tech Help.
$1999.99
Pictures of the kit with measurements click here
Also includes:
1x 4-barrel hand Tig welded aluminum "T" manifold with 1 3/4" center section.
See Picture of Manifold click here
1x Pair of matching 1 3/4" End Castings. These have an extra 2" longer clamping
surface for perfect seal and high boost use!
2x 1 3/4" silicone 7-lair boots for use up to 30psi.
4x 1 3/4" USA made Clamp-Co Stainless Steel T-Bolt clamps.
System works best with a Crank Trigger signal.
More info about our Crank Trigger kits
click here.

Add Port Injection to your kit!
We can mount one or two injectors in each end-castings manifold for true
Port Injection for maximum throttle response!!
Click Here

Port Injection 2x 150hp (up to 300hp use)
One injector on each side. add them to each of your end-castings.
Yes 300hp from just four injectors!!!
This includes 2x USA made CNC injector mounts, Labor to welded in place, All the AN fittings,
hose and labor to extend injector harness and block injector ports in our unit.
Add $275 You must supply your end-castings.
Same but with one set of new stock end-castings add $89.99
Or same but with one set of Turbo end-castings manifolds add $150

Port Injection 4x 150hp (up to 600hp use)
Two injectors on each side. add them to each of your end-castings or your manifolds.
Yes 600hp from just four injectors!!!
This includes 4x USA made CNC injector mounts, Labor to welded in place, All the AN fittings,
hose and labor to extend injector harness and block injector ports.
Add $425 You must supply your end-castings or manifolds.
Same but with one set of new stock end-castings add $89.99
Or same but with one set of Turbo end-castings manifolds. add $150

Have questions?
Send us an e-mail at
Mrkadron@aol.com